User manual WHIRLPOOL WFW88HEAW DIMENSION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WFW88HEAW. We hope that this WHIRLPOOL WFW88HEAW user guide will be useful to you.


WHIRLPOOL WFW88HEAW DIMENSION GUIDE: Download the complete user guide (584 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WFW88HEAW (6705 ko)
   WHIRLPOOL WFW88HEAW INSTALLATION GUIDE (4216 ko)
   WHIRLPOOL WFW88HEAW (6705 ko)
   WHIRLPOOL WFW88HEAW INSTALLATION GUIDE (4216 ko)

Manual abstract: user guide WHIRLPOOL WFW88HEAWDIMENSION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Water remaining in washer after use may cause damage in low temperatures. See “Washer Care” in your “Use and Care Guide” for winterizing information. Whirlpool Models* 523/4" (1340 mm) 383/4" - 393/4" (948 mm - 1010 mm) 335/16" (846 mm) 27" (686 mm) All dimensions show recommended spacing allowed, except for closet door ventilation openings which are the minimum required. For each arrangement, consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. [. . . ] If a closet door or louvered door is installed, top and bottom air openings in door are required. Custom under counter installation: 383/4" - 393/4" (948 mm - 1010 mm) * For additional details (or information) specific to your model, refer to the Dimension Guide at www. 5" (38 mm) DRAIN SYSTEM Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Top of standpipe must be at least 30" (762 mm) high; install no higher than 96" (2. If you have an overhead sewer and need to pump higher than 96" (2. Top of laundry tub must be at least 30" (762 mm) above floor; install no higher than 96" (2. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. Failure to follow these instructions can result in death, fire, or electrical shock. , AC only, 15- or 20-amp, fused electrical NOTE: To avoid floor damage, set washer onto cardboard before moving it. It is recommended that a separate circuit breaker serving only this appliance be provided. N This washer is equipped with a power supply cord having a 3 prong grounding plug. IMPORTANT: Do not overtighten or use tape or sealants on valve when attaching to faucets or washer. In most standard configurations, hoses will cross over each other when attached correctly. Clear water lines Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to avoid clogs. Connect inlet hoses to washer LEVEL WASHER Leveling your washer properly reduces excess noise and vibration. IMPORTANT: Do not overtighten or use tap or sealants on valve when attaching to faucets or washer. NOTE: To reduce risk of hose failure, replace the hoses every 5 years. n Periodically inspect and replace hoses if bulges , kinks , cuts , Remove cardboard from beneath washer. If not level, tip washer and adjust feet up or down as shown in steps 18 and 19, repeating as necessary. Rock washer to test foot contact Slowly turn on water faucets to check for leaks. Secure drain hose Laundry Tub Standpipe Wall Grip washer from top and rock back and forth, making sure all four feet are firmly on floor. 5" (113 (114 mm) Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with cable tie. [. . . ] If washer is not level, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts clockwise on feet until they are about 1/2" (13 mm) from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise to raise the washer. Recheck levelness of washer and that all four feet are firmly in contact with the floor. HELPFUL TIP: You may want to prop up front of washer about 4" (102 mm) with a wood block or similar object that will support weight of washer. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WFW88HEAW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WFW88HEAW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.