User manual WHIRLPOOL WRS342FIAM WARRANTY INFORMATION
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WRS342FIAM. We hope that this WHIRLPOOL WRS342FIAM user guide will be useful to you.
You may also download the following manuals related to this product:
WHIRLPOOL WRS342FIAM ENERGY GUIDE (403 ko)
WHIRLPOOL WRS342FIAM DIMENSION GUIDE (87 ko)
WHIRLPOOL WRS342FIAM USE & CARE GUIDE (1264 ko)
WHIRLPOOL WRS342FIAM INSTALLATION GUIDE (793 ko)
Manual abstract: user guide WHIRLPOOL WRS342FIAMWARRANTY INFORMATION
Detailed instructions for use are in the User's Guide.
[. . . ] All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product. The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you can register on-line at www. U-LineService. com. The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God, such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation, unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the controls; door reversal; or cleaning the condenser. [. . . ] Lift the door off the bottom hinge.
Figure 16
Remove bottom hinge from cabinet (2 screws) (see Figure 17). Note that there may be a nut behind one or both screws on either side. Align hinge outer edge with cabinet before tightening screws.
5.
13
User's Manual
UL111
UL112
Figure 17
Figure 19
BUSHING
UL113 UL110
Figure 18 6.
Figure 20
Relocate plastic spacer/bushing on bottom of door to opposite side, and place door on bottom hinge pin (see Figure 20). Remove plastic hole plug from door handle and relocate on opposite side. See Figure 21.
7.
14
8.
Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. See Figure 19.
HINGE RIGHT SIDE DOOR SWING LEFT SIDE DOOR SWING
PLASTIC PLUG HOLE RIGHT SIDE HINGE SCREW INVERT SCREW INVERT HINGE
PLASTIC PLUG HOLE
UL115
Figure 21 9. Replace three plastic plugs removed in step 8 into holes on top of unit. Reinstall grille (1 screw).
NOTE
On Combo Model 75A (built-in installations only), changing the door mounting to the left side may interfere with ice bucket removal. To reverse the door mounting on Models Combo 75A and 75R (except Stainless Steel models) perform the following: 1. Remove four plastic plugs in hinge holes, top of cabinet, opposite side (see Figure 22). Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. However, the front grille must NOT be obstructed.
NOTE
Combo Models 29A, 29FF, and 75A require additional clearance when the door opens from the right (see Figures 32 and 33). This additional clearance allows for the ice bucket to be removed from the unit.
Unit Dimensions
Model SP18 95 98 15 Series 29 Series 75 Series Width 13-15/16" 13-13/16" 14-13/16" 14-15/16" 20-13/16" 23-7/8" Height 18-1/2" 24-3/4" 27-3/8" 34 - 35" 28-1/2" 34 - 35" Depth 25-1/4" 17" 20" 23-3/4" 24" 24"
21
User's Manual
NOTE
To ease unit installation and removal, increase the Unit Dimension measurements. It is recommended that the cabinet rough opening dimensions be increased by at least 1/4" over the dimensions given for your unit.
H
W
D
UL118
Figure 31
AT LEAST 1" CLEARANCE REQUIRED IF UNIT IS INSTALLED FLUSH WITH CABINET OR WALL. 1. 000
AT LEAST 9" REQUIRED IF UNIT IS INSTALLED ADJACENT TO CABINET OR WALL. 9. 000
CABINET OR WALL CABINET OR WALL
UL126
UL125
Figure 32
Figure 33
22
INITIAL START-UP
Once installation is complete, the unit is ready for initial start-up and operation.
NOTE
Models BI-95 and BI-98 have the ON-OFF switch behind the front grille. A small opening in the top of the grille is provided to access the switch (see Figure 34). Some models may also turn off when the temperature control is turned all the way towards warmer until it stops (clicks). 3.
UL503
Figure 34
Plug the appliance cord into a 115V polarized and grounded electrical outlet. As soon as the ice maker mold reaches the proper temperature, the ice maker mechanism will fill the mold with water. Allow 2 hours for any Frostfree models.
It is possible that dirt or scale will dislodge in the water line. Always throw away all ice cubes made during the first two to three hours of operation.
Allow unit temperature to stabilize for 24 hours before use.
23
User's Manual NORMAL OPERATION
On units with refrigerator sections, the unit has been designed to achieve a fresh food temperature of approximately 38°F (temperature may vary due to ambient temperature). [. . . ] Remove the light housing cover by sliding the cover toward the tab, swinging the end opposite the tab down and pulling down and away (see Figure 43). Replace the light housing cover by inserting the tab FIRST, sliding the cover toward the tab and pushing up the other end. 3.
2
UL305
3
Figure 43
29
User's Manual DEFROSTING CAUTION
DO NOT use any type of electrical heating device, ice pick, knife, or other sharp instrument to defrost, as this could damage the inner lining or refrigeration system and void the warranty. Manual defrost models should be defrosted approximately every 8 weeks. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WRS342FIAM
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WRS342FIAM will begin.