User manual XTANT 403A

[. . . ] Vivid mobile audio, a continuing evolution of the art of listing and hearing, well. We have united art of the technology and the technology of the art to create the magic. Xtant is only available through the finest specialized mobile audio retailers. Your Xtant Select Dealer was chosen by us because of their passion for excellence and their commitment to expanding their expertise. [. . . ] It also increases input sensitivity which "widens the scope" of head units for use with the 403a Modular Expansion Ports: The 403a is supplied with five modular port(s). Four of the ports are dedicated to the amplifier and allow you to dock any of Xtant's signal processing modules. The fifth port is reserved for add on signal processing to the RCA line outputs. The modular method of system expansion is a convenient means of adding the level(s) of signal processing to satisfy your unique system requirements. resistor modules / passive speaker terminals: The Resistor Modules (RM) serve two purposes. First, they activate the "passive speaker terminals" and attenuate (turn down) the level of any speakers connected to these terminals. Designed to power the rear fill speakers, the "passive terminals" may be used with any speakers that you desire to attenuate (ie tweeters / center channel). The RM Modules offer four levels of attenuation: -4, -8, -12, or -16 dB. Protection Circuitry: Both Thermal and Overcurrent protection are incorporated into the 403a. In the event of a problem, either thermal or overcurrent protection will reduce amplifier power to maintain operation. Status LEDs: Three LEDs, visible through the cover, indicate operational status of all Xtant amplifiers. The red LED illuminates when the amplifier is "ON", the yellow LED indicates that overcurrent protection is employed and the orange LED glows when the thermal protection circuit is operational. 5 Xtant 403a SPECIFICATIONS Frequency Response Number of Channels Watts per Channel @ 4 Watts per Channel @ 2 Stereo Ch. Bridged @ 4 Distortion (THD) Signal to Noise Ratio Damping Factor Input Sensitivity 5 Hz to 50 kHz +/­ 3 dB 3 2 x 50 + 1 x 100 2 x 100 + 1 x 200 1 x 200 < . 04% > 100 dB > 200 @ 100 Hz with 4 Load 100 mV to 8. 5 V RMS Unbalanced Source 100 mV to 17 V RMS Balanced Source 0 dB +/­ 20 dB, Selectable in 10 dB Steps Yes CM12HP & CM12LP Included 4 for Amplifier and 1 for Line Outputs Fully Regulated, Pulse Width Modulated 11 to 15 Volts No On-Board Fuse 60 Amp 18. 5 x 7. 6 x 2. 25" Limited 4 Year Parts and Labor ELEVEN OF THIS MANUAL FOR COMPLETE DETAILS Input to Line Output Gain Line Outputs: Crossover Module Ports Power Supply Operational Voltage Fusing Fusing Requirement Size (L x W x H) Warranty SEE PAGE 6 Adding Accessories Modules The 403a is equipped with five accessory docking ports. The four ports dedicated to the amplifier are labeled Amp Vert/Horiz Acc Port and Amp Vert Acc Port. The fifth port is dedicated to the RCA line outputs and is labeled Line Out Vert Acc. Xtant offers two types of accessory modules which are designed for either "Horizontal" or "Vertical" mounting. The docking port, located behind the RCA line outputs, labeled Amp Vert/Horiz Acc Port will accept any module, while the ports labeled "Vert" will only accept modules designed for vertical mounting. The following is a list of Xtant Accessory Modules including their "Horizontal" or "Vertical" mounting design: XTANT ACCESSORY MODULES Mounting Model Function Mounting HORIZ HORIZ VERT CM12H CM12L NGM-1 XOVER XOVER NOISE GATE VERT VERT HORIZ Model CM 24X PQM-1 LFQ 45 Function XOVER EQ BASS EQ The four accessory ports dedicated to the amplifier allow you to add the level(s) of signal processing that your system requires. An example would be if a band pass function is required, a CM12H (high pass at the lowest frequency of the band pass) and a CM12L (low pass at the highest frequency of the band pass) could be used to create a 12 dB per octave band pass filter. A more basic set-up would be a PQM-1 EQ module and a CM 12 crossover module. The Line Out Vert Acc Port will only accept one of the "vertical" accessory modules. This allows bass equalization or a crossover function to be dedicated to the RCA line outputs. [. . . ] If an Authorized Xtant Dealer is not available, please contact Xtant's Customer Service Department for assistance. ELECTRONICS X t a n t Te c h n o l o g i e s 7676 South 46th Street Phoenix, Arizona 85040 888-449-8268 SPEAKERS X t a n t Te c h n o l o g i e s 805 Woodman Ave. Winslow, Il 61089 800-556-2888 TO RETURN XTANT PRODUCTS OUT OF WARRANTY: Contact Xtant's Warranty Department at (602) 431 8686 from 8:00 am to 5:00 pm (MST) for a Return Authorization Number. Please include a description of the problem and, if desired, a request for an estimate of repair costs. [. . . ]