User manual ZONET ZEW2542

[. . . ] Use Zero Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 18 Chapter 6. Soft AP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 23 6. 1 Start Soft AP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 23 6. 2 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 24 6. 3 Access Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 25 6. 4 MAC Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 26 6. 5 Switch to Working Station Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 26 Chapter 7. Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 27 Chapter 8. TroubleShooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 28 802. 11n Wireless USB Adapter Chapter 1 Introduction 1. 1 Welcome Thank you for purchasing Zonet ZEW2542-802. 11n wireless USB adapter. [. . . ] If the authentication type is using TLS/Smart Card, this box is always checked. Allow unauthenticated provision mode: This box is always checked and can not be modified. Use protected authentication credential: If the authentication type is using EAP-FAST, you can use protected authentication credential by check this box. Import: Import the authentication credential file (PAC or al file format), you'll be prompted to select a credential file from your computer. This pull-down menu is only available when authentication type is using PEAP or TTLS. When using EAP-FAST as authentication type, the protocol setting is always Generic Token Card and can not be changed. Password Mode: Select the password mode of EAP-FAST authentication mode. This setting is hidden when the authentication type is not EAP-FAST. 11 802. 11n Wireless USB Adapter 4. 2 Link Status Link status page shows detail information about the current connection. 1. If there's no active connection currently, "Disconnected" will be displayed. Link Quality: Based on signal strength and TX/RX packet error rate (%) 5. Transmit: Link Speed: Shows current transmitting rate (Mbps) Throughput: Shows current transmitting throughput (Kbps) 8. 8. WPS AP List: Display the information of surrounding APs with WPS IE from last scan result, including SSID, BSSID, Channel, ID (Device Password ID), Security-Enabled. Information: Display the information about WPS IE on the selected network, list including Authentication Type, Encryption Type, Config Methods, Device Password ID, Selected Registrar, State, Version, AP Setup Locked, UUID-E and RF Bands PIN Code: 8-digit numbers. Config Mode: Enrollee or external Registrar Detail: Information about Security and Key in the credential. Rotate: Connect to the next network inside credentials. 17 802. 11n Wireless USB Adapter 9. PIN: Start to add to AP using PIN configuration method PBC: Start to add to AP using PBC configuration method Note: When clicking PIN or PBC button, please don't click Rescan within two-minute. If you want to abort this setup within the interval, restart PIN/PBC or press Disconnect to stop WPS. 14. WPS associate IE: Send the association request with WPS IE during WPS setup. WPS probe IE: Send the probe request with WPS IE during WPS setup. 4. 8 About Display information about ZEW2542, such as Utility version/date, Driver version/date, EEPROM version and Firmware version. 18 802. 11n Wireless USB Adapter Chapter 5 Use Zero Configuration Windows XP and Vista has a built-in wireless network configuration utility "Windows Zero Configuration" (WZC). It is a built in service to configure your wireless clients from Windows 1. Start using WZC, right click the tray utility as Configuration utility. and select Use Zero Configuration 2. The windows wireless network connection will appear, double click the wireless network icon on the system tray to check the wireless network, choose the network and click Connect to setup the association. 3. [. . . ] Nothing happens when I click Launch config utilities Please make sure ZEW2542 is inserted into your computer's USB port. If the Ralink configuration utility's icon is black, ZEW2542 is not detected by your computer. I can not establish connection with a certain wireless access point Click Connect for few more times. If the SSID of access point you wish to connect is hidden (nothing displayed in SSID field in Site Survey function), you have to input correct SSID of the access point you wish to connect. [. . . ]